Modern Design Australia Standard Kitchen Cabinets Direct From China

Product Overview

The Modern Design Australia Standard Kitchen Cabinets range is a modular system drawn to the module sizes Australian kitchen suppliers and installers work with every day, produced in our workshops in Guangdong and shipped direct to your project or warehouse. Wall, base, tall and island-base units share one carcass and one hardware family, so a run can be planned as a straight galley, an L, a U or an island without mixing drilling patterns or finishes. Nothing here is a fixed catalogue line — the drawing you approve is what the workshop cuts, which is what lets one specification cover a whole apartment block. Where the specification is standard the range is quick to quote; where it is not, the same line takes the variation. The range is built for the modern kitchen cabinets Australia trade — importers, dealers and fit-out contractors who need one specification to repeat across a development rather than a single bespoke kitchen.

Cabinet Sizes & Module Planning

• Wall cabinets — 720 mm high, 350 mm deep. Shallow enough to stay out of the sightline above a worktop, tall enough for two shelf levels of plates and glasses.
• Base cabinets — 600 mm wide, 700 mm high. The workhorse module: drawer stacks, door-and-shelf units and sink housings all use the same carcass footprint.
• Tall cabinets — 600 mm wide, 2250 mm high. For oven towers, larder storage and fridge housings, with the height taken up at the base rather than by cutting panels on site.
• Island base units — 700 mm wide. Wider than a standard base, so a run can carry a sink, a hob or a seating overhang without a visible join on the face.
• Adjustable legs take up floor tolerance. Screed is rarely dead flat across a whole apartment, and legs let the fitter level each unit before the worktop is fixed instead of packing under a carcass.
• Plan the run before the order. Add module widths against the wall, allow appliance gaps and filler panels at each end, and check the worktop overhang. This is where a modular kitchen cabinet design earns its keep: change a width on the drawing and the whole quotation moves with it.
• Sizes are custom, not fixed. The figures above are the reference modules; if the plan needs a 480 mm base or a 2400 mm tall unit, the carcass is cut to that size. Send the plan and we will confirm the module set — buyers running modern kitchen cabinets Australia projects usually find the reference sizes already fit.

Project & Trade Applications

Multi-unit residential fit-out. A buyer delivering a turnkey apartment building needs hundreds of kitchens that are identical where it matters — same module sizes, same door colour, same hinge — and different only where the plan changes. We quote unit by unit against the floor plans, so tower A and tower B can be produced in separate phases without a colour or drilling difference between them. Hospitality and boutique hotels. Wet bars, guest-room kitchenettes and back-of-house servery joinery take far more traffic than a home kitchen. Lacquer and PVC faces wipe down between guests, drawers run on metal runners, and one specification can cover guest rooms and staff areas so the maintenance team stocks a single set of spares. Where a hotel specifies a stainless steel kitchen cabinet for the back of house, that is quoted as a separate build alongside the guest-facing joinery. Export brands and private label. If you sell under your own name, the cabinets carry your label and your finish, packed for a sea leg and a local installation crew. Clean slab fronts and a controlled palette travel well: the range you approve is the range your dealers receive, container after container. Dealer showrooms and range refreshes. A dealer adding a display kitchen usually wants one or two sets in a finish that will still look current next season. – Even reflection across a full run. Two-pack lacquer is sprayed and polished rather than pressed onto the panel, so the sheen stays consistent from the first door to the last — the thing anyone notices on a long wall of cabinets, and the reason buyers specify a high gloss lacquer kitchen cabinet for open-plan layouts. – Wipe-clean faces. Grease, fingerprints and splashes come off with a damp cloth and a dry one after it. There is no grain to trap marks along the handle line, which is what keeps serviced apartments turning over quickly. – Hardware built for daily use. Damped hinges and metal drawer runners take the everyday slam of a family kitchen, and the standard hinge pattern means spares are a catalogue item rather than a special order. – Shelving that stays straight. Panels are thick enough to carry a full load of plates and pans without a visible bow, so a larder has not sagged by year three. – A profile that will still look current. Slab fronts and a controlled palette age better than a strong grain or an oversized handle, which matters when a dealer range has to sell for several seasons. – Repeatable unit to unit. Every cabinet in an order is cut to the same drawings and the same batch references, so a hundred kitchens behave like one. – Quoted from drawings. As a custom kitchen cabinet supplier we price line by line against your elevations, so you can see what a change costs before you commit to it.

Specifications

Doors, Finishes & Colour Matching

Two-pack high gloss lacquer. The standard door is MDF sprayed and polished in two-pack lacquer. It gives a flat, deep sheen and a face a cloth clears in one pass, which is why a high gloss lacquer kitchen cabinet holds up better than most in a busy family kitchen or a serviced apartment that is cleaned every week.

High gloss PVC membrane. Where the budget or the site calls for it, doors can be pressed in PVC membrane instead. A high gloss PVC kitchen cabinet gives a similar reflective face with a slightly softer touch and no spray line at the edge, and it is the usual choice for wet-bar joinery, utility rooms and rental-grade fit-outs where doors take knocks rather than heat.

Acrylic and solid wood. Acrylic fronts sit between lacquer and PVC for depth of colour, and solid timber doors bring a warmer, more traditional read to the same carcass. Both are quoted per project and neither changes the module sizes.

Stainless steel. Stainless steel appears in this range as a toe-kick option and as the sink grade. If the specification is a full stainless steel kitchen cabinet — commercial kitchens, back-of-house, wet zones — say so at enquiry stage: that is a different build from the timber carcass shown here and it is quoted separately.

Colour matching. Colour is customized, and the reference you approve is the reference we spray. Send a physical sample or a colour code with the order, and on phased projects keep the same reference on file so the second block matches the first. Agree the sheen at the same time, because two gloss levels of one colour read differently under kitchen lighting.

Door profiles and edges. Slab fronts, as shown, are the cleanest option for a contemporary kitchen and the easiest to wipe down — the front most modern kitchen cabinets Australia buyers start from. If a project calls for a framed or shaker door instead, raise it at enquiry stage and we will confirm what the workshop can produce on the same carcass. Edge banding is matched to the face so the door reads as one piece when it is closed.

Countertops, Sinks & Hardware

• Countertops quoted with the cabinets. Man-made stone, quartz, marble, solid surface, acrylic and laminate can all be priced alongside the units, so the worktop arrives on the same schedule as the cabinets it sits on. A flat/eased edge reads sharpest under a slab door; a bullnose softens a family kitchen where people lean on the counter.
• Sink and tap coordination. Stainless steel or zinc alloy sinks can be supplied with the order, and the sink housing is built to the cut-out rather than cut on site — which matters most on a stainless steel kitchen cabinet run, where a misplaced hole cannot be patched.
• Drawer internals specified up front. Baskets, cutlery trays and concealed slides are chosen with the unit, so a deep pan drawer arrives ready to use instead of being retrofitted after handover. – Corner storage. Lazy Susan carousels for base corners and pull-outs for tall larders make the awkward parts of a modular kitchen cabinet design usable. Specify them at quotation stage, because fitting them into a finished run means taking the worktop off.
• Handles, knobs and plinth. Handle and knob ranges are chosen alongside the door finish, and the toe kick can match the door or switch to aluminium, stainless steel or PVC where the plinth takes more punishment.
• Backsplash. A matching or contrasting backsplash panel can be cut with the worktop, keeping the joint line between worktop and wall consistent across every unit in the order. – One accessory schedule per project. As a custom kitchen cabinet supplier we quote handles, hinges, runners and internals line by line, so a repeat order arrives with the same parts rather than a near match.

Care & Cleaning

High gloss surfaces are easy to keep, as long as the cloth is the right one. A damp microfibre cloth followed by a dry one handles day-to-day marks; abrasive pads, scouring cream and solvent cleaners dull the lacquer and leave a patch that shows under a downlight. Wipe splashes from the hob and the sink area as they happen rather than at the end of the week, because standing water and cooking oil are what mark panel edges first.

On a high gloss PVC kitchen cabinet the same routine applies with one extra habit: do not leave strong solvents or adhesive residue on the face, since PVC membrane softens where lacquer would simply smear. Sticky labels and tape come off with warm water and a little washing-up liquid, not with a scraper.

Hinges and runners do not need oiling — a drop of oil attracts dust and grit into the mechanism. If a door has dropped or a drawer is catching, adjust the hinge or the runner rather than forcing it; the adjustment screws sit on the hinge body and under the runner.

Keep the plinth clear. A toe kick is a panel, not a seal, so mop water should not be left standing against it, and any leak under the sink should be dried out with the cabinet interior left open to air. Where a property is deep-cleaned by a contractor between tenants, pass these points on: no abrasives, no solvents, no standing water.

Ordering & Delivery

1. Send the drawings. Floor plans, elevations and a room schedule are enough to start; a hand sketch with dimensions works too if that is what you have.
2. Confirm the specification line by line. Door finish, carcass board, board grade, hardware brand, worktop, sink, accessories and colour reference are fixed on paper before production. Because we are a kitchen cabinet manufacturer China-based, the sheet you approve is the sheet the workshop builds to — it is not re-typed by a trading office in between.
3. Check the finish against a sample. Colour and sheen are the two things photographs cannot settle. Ask your sales contact which finish samples are available for the colour you have chosen, and approve one before the panels are sprayed.
4. Choose the packing format. Assembled units arrive ready to set and fix; knock-down panels arrive flat, for lower freight volume and local assembly. Decide before the packing list is drawn, because it changes carton counts and container planning.
5. Book the production slot. Standard work is generally running at around 15 days; your sales contact will confirm the current schedule against your delivery dates and any phase splits.
6. State your market’s documentation needs. If the destination market asks for particular test reports, marking or paperwork, raise it at enquiry stage so we can confirm what can travel with the order rather than after it ships.
7. Agree the after-sales route. Installation guidance can be shared before your team starts on site. Report shortages or transit damage against the packing list, and keep the carton labels until the last unit is installed.
8. Set the order volume. Single sets for a showroom and multi-container programmes both run through the same line. Tell your sales contact the volume you expect for the season — wholesale modern kitchen cabinets programmes get a production slot booked against a selling season rather than against a single delivery date.

Scale & Supply Capability

We are a China-based whole-house cabinet manufacturer supplying wholesalers, trade buyers and project buyers. Our ISO9001-certified factory produces to buyers’ own drawings, sizes and finishes, and we support OEM and private-label programmes for customers building their own catalogue. Every order is quoted and scheduled around your volumes and delivery dates, with packing and export documents handled on our side. Send your quantities, sizes and destination port, and we will come back with the production schedule and shipping plan.

FAQ

What does “Australia standard” mean on these cabinets?

It describes the module sizes and construction the range is drawn to — the wall, base, tall and island-base dimensions that Australian kitchen installers and suppliers work with, matched to a consistent carcass build and standard hinge patterns, so a fitter is not re-drilling panels on site. It is not a compliance or certification claim: if your project needs particular test reports, marking or documentation for the destination market, tell us at enquiry stage and we will confirm what can be supplied with the order. When comparing quotes from one custom kitchen cabinet supplier to another, ask each to state module sizes and board grade in writing — that is usually where the quotes differ.

Can the cabinets be supplied under our own brand?

Yes. Cabinets can carry your brand rather than ours — on door backs, carcass labels or the plinth, depending on what your market expects. Because we are a kitchen cabinet manufacturer China-based, artwork and labelling are handled at production instead of being added later by a third party, so what lands in your warehouse is already your product. Send the brand artwork and the positions you want it in along with the order drawings.

How do the lacquer, PVC and stainless steel options compare?

Two-pack lacquer gives the deepest, flattest reflection and is the finish most people mean by a high gloss lacquer kitchen cabinet; it is sprayed and polished, and it wipes clean in one pass. A high gloss PVC kitchen cabinet uses a pressed membrane face instead — a similar reflection, a slightly softer touch and no spray line at the edge — which suits high-turnover and rental work. Stainless steel is a different build rather than a different door face, specified for commercial or wet-area use and quoted separately from the timber carcass range. Colour choice is widest in lacquer, so if the palette is the fixed point, start there.

Which hinges and drawer runners are fitted?

Blum or DTC, with dampers on every door. Both use standard hinge patterns, so a fitter can carry spares instead of ordering them per project, and both brands’ runners are available on drawers. If a specification names one brand specifically, say so when the order is confirmed — the hardware brand is fixed on the specification sheet before production and stays the same on every unit of that order.

How do I plan a modular kitchen cabinet design across a multi-unit project?

Start from the module sizes and repeat them. The reference wall and base units give you the grid; from there the differences between one apartment and the next are usually appliance positions, sink locations and whether the run ends in a tall unit. Keep one colour reference, one hardware brand and one edge banding across the whole project so nothing drifts between phases. Then check the three things that cause site delays: service voids behind tall units, hob and sink cut-outs against the worktop drawing, and the toe-kick height against finished floor level. Send the plans and we will map the module set unit by unit before quoting — this is the point where a wholesale modern kitchen cabinets order either runs smoothly or starts collecting variations.